{"title":"MATEKSYS","description":"","products":[{"product_id":"fc-mateksys-f405-wing-v2","title":"FC MATEKSYS F405-WING-V2","description":"\u003cp\u003eFC specification\u003c\/p\u003e\n\u003cp\u003eMCU: STM32F405RGT6, 168MHz, 1MB Flash \u003cbr\u003eIMU: ICM42688-P \u003cbr\u003eBarometer: DPS310 \u003cbr\u003eOSD: AT7456E \u003cbr\u003eBlackbox: MicroSD card slot \u003cbr\u003e6x UART, 1x Softserial_Tx option (INAV) \u003cbr\u003e10x PWM outputs \u003cbr\u003e2x I2C \u003cbr\u003e3x ADC (VBAT, Current, RSSI) \u003cbr\u003eBuilt-in inverter for SBUS input \u003cbr\u003eUSB Type-C (USB 2.0)\u003c\/p\u003e\n\u003cp\u003eFirmware FC\u003c\/p\u003e\n\u003cp\u003eArduPilot: MatekF405-Wing (ArduPlane 4.4 or later) \u003cbr\u003eINAV: MATEKF405SE (INAV 6.0 or later)\u003c\/p\u003e\n\u003cp\u003ePDB\u003c\/p\u003e\n\u003cp\u003eInput voltage: 9~30V (3~6S LiPo) with TVS protection \u003cbr\u003eCurrent sensor: 220A, 3.3V ADC (INAV scale 150, ArduPilot 66.7A\/V) \u003cbr\u003eSensor resistor: 100A continuous, 220A peak \u003cbr\u003eBattery voltage divider 1K:10K (Scale 1100 v INAV, BATT_VOLT_MULT 11.0 in ArduPilot)\u003c\/p\u003e\n\u003cp\u003eBEC 5V output\u003c\/p\u003e\n\u003cp\u003eDesigned for flight controller, receiver, OSD, camera, buzzer, 2812 LED strip, buzzer, GPS module, air speed sensor \u003cbr\u003eContinuous current: 2A\u003c\/p\u003e\n\u003cp\u003eBEC 9V \/ 12V output\u003c\/p\u003e\n\u003cp\u003eDesigned for video transmitter, camera, gimbal etc. \u003cbr\u003eContinuous current: 2 A \u003cbr\u003e12V option with jumper \u003cbr\u003eFor stable 9V\/12V output, input voltage should be higher than +1V output voltage\u003c\/p\u003e\n\u003cp\u003eBEC Vx output\u003c\/p\u003e\n\u003cp\u003eDesigned for servos \u003cbr\u003eAdjustable voltage, 5V default, 6V or 7.2V options \u003cbr\u003eContinuous current: 5A, peak current 6A \u003cbr\u003eFor stable Vx output, input voltage should be higher than Vx voltage +1V\u003c\/p\u003e\n\u003cp\u003eBEC 3.3V output\u003c\/p\u003e\n\u003cp\u003eDesigned for external 3.3V peripherals \u003cbr\u003eLinear regulator \u003cbr\u003eContinuous current: 200 mA\u003c\/p\u003e\n\u003cp\u003ePhysical parameters\u003c\/p\u003e\n\u003cp\u003eMounting: 30.5 x 30.5 mm, Φ4 mm with Φ3 mm rubber grommets \u003cbr\u003eDimensions: 54 x 36 x 13 mm \u003cbr\u003eWeight: 25 g\u003c\/p\u003e\n\u003cp\u003ePackage contents:\u003c\/p\u003e\n\u003cp\u003e1x F405-Wing-V2 \u003cbr\u003e1x 20cm JST-GH-4P to JST-GH-4P cable for I2C port \u003cbr\u003eDupont 2.54 pins\u003c\/p\u003e","brand":"Baltic Drones","offers":[{"title":"Default Title","offer_id":55962296123779,"sku":"5091","price":45.0,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0936\/1873\/3443\/files\/17056-1_f405-wing-v2-4.jpg?v=1752055789"},{"product_id":"fc-mateksys-h743-wing-v3","title":"FC MATEKSYS H743-WING V3","description":"Processor: STM32H743VIT6, 480MHz, 1MB RAM, 2MB Flash (SPI2). \/\u0026gt;\u003cstrong\u003eSPI3 Breakout Output:\u003c\/strong\u003e 1\u003cbr\u003e\u003cstrong\u003eLED:\u003c\/strong\u003e 3 LEDs for FC Status (Blue, Red) and 3.3V BEC Indicator (Red)\u003cbr\u003e\u003cstrong\u003eADC:\u003c\/strong\u003e VBAT, Current, RSSI, Analog AirSpeed, VB2, CU2\u003cbr\u003e\u003cstrong\u003eSeparate Board:\u003c\/strong\u003e USB Type-C \/ Buzzer\u003cbr\u003e\u003cstrong\u003eSwitchable Inputs:\u003c\/strong\u003e For dual camera use\u003cbr\u003e\u003cstrong\u003eBEC Switch:\u003c\/strong\u003e 5V\/9V (12V)\u003cbr\u003e\u003cstrong\u003eHigh Precision Current Sensor:\u003c\/strong\u003e Yes\u003cbr\u003e\u003cstrong\u003eADC Voltage Divider VB2:\u003c\/strong\u003e 1K:10K\u003cbr\u003e\u003cstrong\u003eADC Voltage Divider AirSpeed:\u003c\/strong\u003e 10K:10K\u003cbr\u003e\u003cstrong\u003eINAV TR\/SA VTX Control:\u003c\/strong\u003e Yes\u003cbr\u003e\u003cstrong\u003eBuzzer Support:\u003c\/strong\u003e Yes\u003cbr\u003e\u003cstrong\u003eRSSI:\u003c\/strong\u003e Yes\u003cbr\u003e\u003cstrong\u003eAnalog Airspeed Sensor Connection:\u003c\/strong\u003e Yes\u003cbr\u003e\u003cstrong\u003eDigital Airspeed Sensor Connection:\u003c\/strong\u003e Yes\u003cbr\u003e\u003cstrong\u003eStatic Power Consumption:\u003c\/strong\u003e 160mA at 5V\u003cbr\u003e\u003cstrong\u003eFirmware INAV:\u003c\/strong\u003e MATEKH743\u003cbr\u003e\u003cstrong\u003eFirmware ArduPilot (ChiBiOS):\u003c\/strong\u003e MATEKH743\u003cbr\u003e\u003cstrong\u003eFirmware BetaFlight:\u003c\/strong\u003e MATEKH743\u003cbr\u003e\u003cstrong\u003eMounting:\u003c\/strong\u003e 30.5 x 30.5mm, hole diameter 4mm, with 3mm spacers\u003cbr\u003e\u003cstrong\u003eDimensions:\u003c\/strong\u003e 54 x 36 x 13 mm\u003cbr\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 30 g (with USB extension)","brand":"Baltic Drones","offers":[{"title":"Default Title","offer_id":55962296484227,"sku":"5089","price":105.0,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0936\/1873\/3443\/files\/17059-1_h743-wing-v3-3.jpg?v=1752055794"},{"product_id":"fс-mateksys-h743-slim-v3","title":"FС MATEKSYS H743-SLIM V3","description":"\u003cp\u003eFС Mateksys H743-SLIM V3\u003c\/p\u003e\n\u003cp\u003eThe H743-SLIM V3 flight controller is equipped with an ultra-fast modern H7 processor with a frequency of 480 MHz and 1 MB RAM! It weighs just 7 grams and measures 36 x 36 mm. It features an Infineon DPS310 precision barometer, dual ICM42688-P and ICM42605 gyroscopes, a MicroSD slot for data logging and 7 UART ports – including support for FPV systems such as DJI.\u003c\/p\u003e\n\u003cp\u003eLike its larger counterpart, the H743-WING, it includes a CAN BUS port for connecting advanced peripherals. However, the H743-SLIM is more suitable for quadcopters as it does not have a PDB and several BEC voltage regulators, although it remains flexible enough to be used in a variety of RC models, including fixed-wing aircraft.\u003c\/p\u003e\n\u003cp\u003eH743-SLIM V3 is compatible with ArduPilot (4.2 or later), BetaFlight (4.3 or later) and INAV (5.0 and later), giving you the freedom to choose the firmware that best suits your setup.\u003c\/p\u003e\n\u003cp\u003eSpecifications\u003c\/p\u003e\n\u003cp\u003eMCU: STM32H743VIH6, 480MHz, 1MB RAM, 2MB Flash\u003cbr\u003eV1.0 IMU Board: MPU6000 (SPI1) and ICM20602 (SPI4)\u003cbr\u003eV1.5 IMU Board: MPU6000 (SPI1) and ICM42605 (SPI4)\u003cbr\u003eBaro: Infineon DPS310 (I2C2). analog air speed, Vbat2, Cur2)\u003cbr\u003e3x LEDs for FC STATUS (blue, red) and 3.3V indicator (red)\u003cbr\u003e1x SPI3 hub\u003cbr\u003eUSB Type C (USB 2.0)\u003cbr\u003e1x JST-SH1.0_8pin connector (Vbat\/G\/Curr\/Rx8\/S1\/S2\/S3\/S4)\u003cbr\u003e1x connector JST-GH1.25_4pin (5V\/CAN-H\/CAN-L\/G)\u003cbr\u003eCamera Dual Input Switch\u003cbr\u003e5V\/Vbat Filtered Power Switch\u003cbr\u003eDJI FPV OSD is supported by any spare UART\u003c\/p\u003e\n\u003cp\u003ePower supply\u003cbr\u003eVbat input: 6~36V (2~8S LiPo)\u003cbr\u003eBEC: 5V 2A continuously (max. 3A)\u003cbr\u003eLDO 3.3V: max. 200 mA\u003cbr\u003eNo built-in current sensor\u003cbr\u003eADC Vbat2 pad supports max. 69V (voltage divider: 1K:20K)\u003cbr\u003eStatic output: 200mA at 5V with Betaflight, 150mA at 5V with ArduPilot\u003c\/p\u003e\n\u003cp\u003eFirmware FC\u003cbr\u003eArduPilot(ChiBiOS): MATEKH743\u003cbr\u003eBetaFlight: MATEKH743\u003cbr\u003eINAV: MATEKH743\u003c\/p\u003e\n\u003cp\u003ePhysical\u003cbr\u003eMounting: 30.5 x 30.5mm, Φ4mm with Φ3mm grommets\u003cbr\u003eDimensions: 36 x 36 x 5mm\u003cbr\u003eWeight: 7g\u003c\/p\u003e\n\u003cp\u003ePackage includes:\u003cbr\u003e1x H743-SLIM V3\u003cbr\u003e6x M4 to M3 silicone grommets\u003cbr\u003e1x JST-SH1.0_8pin cable, 5cm\u003cbr\u003e2x JST-SH1.0_8pin connectors\u003cbr\u003e1x JST-GH-4P to JST-GH-4P CAN port cable, 20cm\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.myshoptet.com\/usr\/www.hobbydrone.cz\/user\/documents\/upload\/mceclip0-19.jpg?1747745023\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.myshoptet.com\/usr\/www.hobbydrone.cz\/user\/documents\/upload\/mceclip1-3.jpg?1747745039\"\u003e\u003c\/p\u003e","brand":"Baltic Drones","offers":[{"title":"Default Title","offer_id":55963536818563,"sku":"6830","price":99.0,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0936\/1873\/3443\/files\/20222-2_fs-mateksys-h743-slim-v3.jpg?v=1752064335"},{"product_id":"gps-module-mateksys-m10q-5883-with-compass","title":"GPS Module Mateksys M10Q-5883 with compass","description":"\u003cp\u003eGPS module Mateksys M10Q-5883 with compass\u003c\/p\u003e\n\u003cp\u003eMatek M10Q-5883 GNSS \u0026amp; Compass is a high-performance GPS module designed for drones, RC aircraft and other unmanned aerial vehicle (UAV) applications. It combines advanced positioning features with a reliable compass in a compact design.\u003c\/p\u003e\n\u003cp\u003eFeatures:\u003c\/p\u003e\n\u003cp\u003e- The M10Q-5883 uses a multi-constellation GNSS module powered by the u-blox M10 series\u003cbr\u003e- The GNSS module features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition time for all L1 GNSS signals. Supports simultaneous reception of four GNSS (GPS, GLONASS, Galileo and BeiDou). The high number of visible satellites allows the receiver to select the best signals. This maximizes location availability, especially in challenging conditions such as deep urban canyons. u-blox Super-S (Super-Signal) technology offers excellent RF sensitivity and can improve dynamic position accuracy in non-line-of-sight situations.\u003cbr\u003e- 15 x 15mm2 high-gain patch antenna provides the best ratio between performance and small size. The omni-directional radiation pattern of the antenna increases the flexibility when installing the device.\u003c\/p\u003e\n\u003cp\u003eSpecifications:\u003c\/p\u003e\n\u003cp\u003eGNSS module: u-blox SAM-M10Q-00B\u003cbr\u003eSupported GNSS: GPS, GLONASS, Galileo, BeiDou\u003cbr\u003eCompass: QMC5883L\u003cbr\u003eAntenna: 15 x 15 x 4mm patch antenna\u003cbr\u003eInput voltage: 4V to 9V\u003cbr\u003ePower consumption: about 13mA\u003cbr\u003eInterface:\u003cbr\u003e-GNSS: UART (TX, RX)\u003cbr\u003e-Compass: I2C (DA, CL)\u003cbr\u003eConnector: JST-GH-6P (1.27mm pitch)\u003cbr\u003eProtocol: UBX (u-blox) at 5Hz or NMEA at 1Hz\u003cbr\u003eOperating temperature: -20°C to +80°C\u003cbr\u003eDimensions: 20mm x 20mm x 12.4mm\u003cbr\u003eWeight: about 8g\u003c\/p\u003e\n\u003cp\u003ePackage includes:\u003cbr\u003e1x GNSS module and compass M10Q-5883\u003cbr\u003e1x cable\u003c\/p\u003e","brand":"Baltic Drones","offers":[{"title":"Default Title","offer_id":55963610579331,"sku":"6981","price":35.4,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0936\/1873\/3443\/files\/20297_gps-module-mateksys-m10q-5883-with-compass.png?v=1752064490"},{"product_id":"digital-air-speed-sensor-mateksys-aspd-4525","title":"Digital Air Speed Sensor MATEKSYS ASPD-4525","description":"\u003cbody\u003e   \u003cstyle\u003e body { font-family: Arial, sans-serif; font-size: 14px; }\n\n  pre { font-family: Arial, monospace; white-space: pre-wrap; } .highlight { font-weight: bold; } \u003c\/style\u003e \n \u003cpre\u003eMATEKSYS ASPD-4525 Digital Air Speed Sensor The MATEKSYS ASPD-4525 is a lightweight digital air speed sensor designed for fixed-wing drones and RC aircraft. It provides accurate air speed measurements via an I²C connection to flight controllers and ensures reliable performance in a variety of conditions. Compact and easy to install, it includes a Pitot tube and silicone tubing for complete installation. Features: - High-accuracy airspeed measurement (±0.25% SPAN) - Red LED indicator for power status - Seamless I²C connection to flight controllers (e.g., ArduPilot, iNav)\n- Lightweight and durable construction Specifications: Board supply voltage: 4~5.5 V DC Sensor: TE 4525DO-DS5AI001DP Operating current: 5 mA Output: I2C (SCL \u0026amp; SDA) Pressure range: 1 PSI (6.89 kPa)\nMaximum pressure: 20 PSI (137.9 kPa) Operating temperature: -40 °C ~ 125 °C Accuracy: ±0.25% SPAN Red LED: power indicator JST-GH sequence: 5 V, SCL, SDA, GND Weight: 3.5 g (sensor board) Package includes: 1x ASPD-4525 sensor board 1x 20 cm JST-GH-4P to JST-GH-4P silicone cable 1x Pitot tube 1x 40 cm transparent silicone tube\u003c\/pre\u003e\n\u003c\/body\u003e","brand":"Baltic Drones","offers":[{"title":"Default Title","offer_id":57312558776707,"sku":"7629","price":50.0,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0936\/1873\/3443\/files\/22062_digital-air-speed-sensor-mateksys-aspd-4525.jpg?v=1770238216"}],"url":"https:\/\/p1c5mr-sk.myshopify.com\/collections\/mateksys.oembed","provider":"Baltic Drones","version":"1.0","type":"link"}