{"product_id":"baseboard-bundle-holybro-pixhawk-jetson-6x-pro","title":"Baseboard Bundle Holybro Pixhawk Jetson 6X Pro","description":"\n\n\n\u003cstyle\u003e\n  points {\n    font-family: Arial, sans-serif;\n    font-size: 14px;\n  }\n\n  for {\n    font-family: Arial, monospace;\n    white-space: pre-wrap;\n  }\n\n  .highlight {\n    font-weight: bold;\n  }\n\u003c\/style\u003e\n\n\u003cpoints\u003e\n\u003cpre\u003eHolybro Pixhawk Jetson 6X Pro Motherboard Kit\n\nThe Holybro Pixhawk Jetson motherboard is based on the open-source Pixhawk Autopilot Bus specification and the NVIDIA Jetson Orin NX\/Nano carrier board. The Pixhawk Autopilot Bus (PAB) format allows use with any PAB flight controller such as the Pixhawk 6X.\n\nFeatures:\n\n- Combines the performance of Pixhawk and Nvidia Jetson in a single board;\n- Jetson \u0026amp; Pixhawk connectivity via UART, CAN and Ethernet switch;\n- Pixhawk Autopilot Bus (PAB) format;\n- Compatible with Jetson Orin NX \u0026amp; Orin Nano;\n- 2x M.2 slot: Key A\/E for WiFi\/Bluetooth \u0026amp; Key M for NVMe SSD.\n\nProcessors and sensors:\n\nFMU processor: STM32H753  \n- 32-bit Arm® Cortex®-M7, 480 MHz, 2 MB flash, 1 MB RAM  \nIO processor: STM32F103  \n- 32-bit Arm® Cortex®-M3, 72 MHz, 64 KB SRAM  \nIntegrated sensors (current version Rev8):  \n- Accelerometer\/gyroscope: 3× ICM-45686 (with BalancedGyro™ technology)  \n- Barometer: ICP20100 \u0026amp; BMP388  \n- Magnetometer: BMM150  \n\nMotherboard ports and connections:\n\n2x Gigabit Ethernet port  \n- Connected to both Jetson and Autopilot via RTL8367S switch  \n- Powered by Pixhawk circuit  \n- 8pin JST-GH and RJ45  \n2x input for MIPI CSI cameras (4 lines each, 22pin FFC Raspberry Pi)  \n2× USB 3.0 Host (USB-A, 1.5 A)  \n2× USB 2.0 Host (5pin JST-GH, 1.0A)  \nUSB 2.0 for programming\/debugging (USB-C)  \nKey M 2242\/2280 for NVMe SSD (PCIEx4)  \nKey E 2230 for WiFi\/Bluetooth (PCIEx2, USB, UART, I2S)  \nMini HDMI output  \n4x GPIO (6pin JST-GH)  \nCAN port (CAN2, 4pin JST-GH)  \nSPI port (7pin JST-GH)  \nI2C port (4pin JST-GH)  \nI2S port (7pin JST-GH)  \n2× UART port (1 for debug, 1 for Autopilot telem2)  \nFan power supply  \nIMU: IIM42652  \nPower supply:  \n- XT30 connector  \n- Voltage: 7-21V (3S-4S)  \n- Separate power circuits for flight safety  \n- Holybro UBEC 12A (3-14S) can be used for higher input voltage  \n- The board's built-in BEC can only handle 7-21V (3S-4S), the use of UBEC 12A is recommended as a backup  \nPower Requirements:  \n- Min. 8 V \/ 3 A (depends on peripherals)\n\nAutopilot connectors:\n\nPixhawk Autopilot Bus Interface  \n- 100pin and 50pin Hirose DF40  \nBackup digital power inputs  \n- I2C voltage measurement support  \n- 2× 6pin Molex CLIK-Mate  \n- Power selector with overvoltage protection  \nMax. input voltage: 6V  \nUSB input: 4.75-5.25V  \nGPS and security button (10pin JST-GH)  \nSecond GPS port (6pin JST-GH)  \n2× CAN port (4pin JST-GH)  \n3× Telemetry with flow control (2× 6pin JST-GH, 1 connected to UART1 Jetson)  \n16 PWM outputs (2× 10pin JST-GH)  \nUART4 \u0026amp; I2C (6pin JST-GH)  \nAD \u0026amp; IO (8pin JST-GH)  \nUSB 2.0 (USB-C, 4pin JST-GH)  \nDSM input (3pin JST-ZH 1.5mm)  \nRC input (PPM\/SBUS, 5pin JST-GH)  \nSPI for external sensors (11pin JST-GH)  \n2x Debug port (1x for FMU, 1x for IO, 10pin JST-SH)  \nDimensions (without Jetson and FC): 126 x 80 x 38 mm  \nWeight: 203.2g (with Jetson, cooler, FC, SSD, WiFi)\n\nUBEC-12A Specifications:\n\nInput voltage: 3-14S (XT30)  \nOutput voltage: 6.0V \/ 7.2V \/ 8.0V \/ 9.2V (recommended 7.2V for Jetson)  \nOutput current:  \n- Permanent: 12 A  \n- Peak: 24 A  \nDimensions: 48 x 33.6 x 16.3 mm  \nWeight: 47.8 g  \n\nThe package contains:\n\n1 × Pixhawk 6X Pro Flight Controller  \n1 × Pixhawk Jetson Orin Motherboard (with heatsink or without case)  \n1 × Nvidia Orin NX (16GB RAM) \/ Orin Nano (4GB RAM) with cooler and fan  \n1 x SSD: Samsung PM9B1 PCIe 4.0 NVMe 512 GB  \n1 × Wi-Fi \u0026amp; Bluetooth module: Intel 8265NGW AC Dual Band or Realtek RTL8B22CE  \n1 × Camera: IMX219-200  \n1 × PM02D Power Module  \n1 x UBEC 12A (3-14S)  \n1 x PDB board  \n1 × Set of cables\n\n\u003c\/pre\u003e\n\n\u003c\/points\u003e","brand":"Baltic Drones","offers":[{"title":"Default Title","offer_id":55963474461059,"sku":"20338","price":2861.65,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0936\/1873\/3443\/files\/19652_sku20337-20338.jpg?v=1752062797","url":"https:\/\/p1c5mr-sk.myshopify.com\/products\/baseboard-bundle-holybro-pixhawk-jetson-6x-pro","provider":"Baltic Drones","version":"1.0","type":"link"}