{"product_id":"stack-speedybee-f405-v3-bls-60a-30x30-fc-esc","title":"Stack SpeedyBee F405 V3 BLS 60A 30x30 FC\u0026ESC","description":"   \u003cstyle\u003e body { font-family: Arial, sans-serif; font-size: 14px; } for { font-family: Arial, monospace;  white-space: pre-wrap; } .highlight { font-weight: bold;}\u003c\/style\u003e\u003cpre\u003e\nSpeedyBee F405 V3 BLS 60A 30x30 FC\u0026amp;ESC stack\n\nThe SpeedyBee F405 V3 BLS 60A 30×30 FC\u0026amp;ESC Stack is designed to provide unmatched performance and efficiency in free-flying FPV. Whether you're performing complex maneuvers or exploring creative lines, this kit gives you the precision and control you need to push the boundaries of aerobatics. With advanced gyro sensors and intelligent flight algorithms, this pod provides unmatched stability and control, allowing you to perform precise maneuvers with confidence and precision. With a standard 30x30mm form factor, the SpeedyBee stack effortlessly fits most drone frames for hassle-free installation and setup. \n\nSpecifications:\n\nProduct Name: SpeedyBee F405 V3 30x30 Flight Controller\nMCU: STM32F405\nIMU (gyroscope): BMI270\nUSB port type: Type-C\nBarometer: built-in\nOSD chip: AT7456E chip\nBLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with baud rate 115200 on UART4)\nWIFI: Not supported\nDJI air unit connection method: Two ways are supported: 6-pin connector or direct soldering.\nDJI Air Unit 6 Pin Plug: Supported. Fully compatible with DJI O3\/RunCam Link\/Caddx Vista\/DJI Air Unit V1, no need to change any cable.\nBlackbox MicroSD card slot: Betaflight firmware requires the microSD card type to be either standard (SDSC) or high capacity (SDHC), so extended capacity (SDXC) cards are not supported (many high-speed U3 cards are SDXC). The card MUST also be formatted with a FAT16 or FAT32 file system (recommended). So you can use any SD card smaller than 32GB, but Betaflight can only recognize a maximum of 4GB.\nBetaFlight Camera Control Pad: Yes (CC pad on front)\nCurrent sensor input: Supported. For the SpeedyBee BLS 60A ESC, set Scale = 400 and Offset = 0.\nPower Input: 3S - 6S Lipo (via G, BAT pins\/pads from 8-pin connector or 8-pads on bottom)\n5V output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad (used for buzzer) on the front and 4x LED 5V pads. The total current load is 2A.\n9V output: 2 groups of 9V output, one +9V pad on the front and the other included in the connector on the bottom. The total current load is 2A.\n3.3V output: Supported. Designed for receivers with 3.3V input. Current load up to 500 mA.\n4.5V output: Supported. Designed for the GPS receiver and module, even if the FC is powered via the USB port. Current load up to 1A.\nESC signal: M1 - M4 on the bottom side and M5-M8 on the front side.\nUART: 6 sets (UART1, UART2, UART3, UART4 (reserved for Bluetooth connection)), UART5 (reserved for ESC telemetry), UART6\nESC telemetry: UART R5\nI2C: Supported. SDA \u0026amp; SCL pads on the front. Used for magnetometer, sonar, etc.\nTraditional Betaflight LED Pad: Supported. 5V, G and LED pads on the bottom of the front. Used for WS2812 LEDs controlled by Betaflight firmware.\nBuzzer: BZ+ and BZ- pad used for 5V buzzer\nBOOT Button: Supported\nSSI Input: Supported. Named as RS on the front.\nSmart Port \/ F.Port: Not supported\nSupported Flight Controller firmware: BetaFlight (default), INAV (INAV firmware can only use Multishot (recommended) and OneShot125. Please note that DShot is not supported.)\nTarget firmware name: SPEEDYBEEF405V3\nMounting: 30.5 x 30.5mm (hole diameter 4mm)\nDimension: 41.6 (L) x 39.4 (W) x 7.8 (H) mm\nWeight: 9.6g\n\nProduct name: SpeedyBee BLS 60A 30x30 4-in-1 ESC\nFirmware: BLHeli_S J-H-40\nPC Configurator download link: https:\/\/esc-configurator.com\/\nContinuous current: 60A * 4\nExplosive current: 80A (10s)\nTVS protection diode: Yes\nExternal capacitor: 1000uF Low ESR capacitor (included)\nESC protocol: DSHOT300\/600\nPower: 3-6S LiPo\nOutput power: VBAT\nCurrent Sensor: Support (Scale=400 Offset=0)\nESC telemetry: Not supported\nMounting: 30.5 x 30.5mm (hole diameter 4mm)\nDimension: 45.6 (L) * 44 (W) * 8 mm (H)\nWeight: 23.5g\n\nThe package includes:\n1x SpeedyBee F405 V3 flight controller\n1x ESC SpeedyBee BLS 60A 4in1\n1x 35V 1000uF Low ESR capacitor \n5x M3 nylon nut\n5x M3 silicone O-ring\n1x M3*8mm silicone grommets (for FC)\n1x M3*8.1mm silicone grommets (for ESC)\n1x SH 1.0mm 25mm long 8pin cable (for FC-ESC connection)\n5x M3*30mm hexagon socket head screws\n1x DJI 6pin cable (80mm)\n1x XT60 power cable (100mm)\n\u003c\/pre\u003e","brand":"Baltic Drones","offers":[{"title":"Default Title","offer_id":55962025525635,"sku":"SB-F4V3-60-STACK","price":93.16,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0936\/1873\/3443\/files\/15726-9_15726-stack-speedybee-f405-v3-bls-60a-30x30-fc-esc.jpg?v=1752052242","url":"https:\/\/p1c5mr-sk.myshopify.com\/products\/stack-speedybee-f405-v3-bls-60a-30x30-fc-esc","provider":"Baltic Drones","version":"1.0","type":"link"}