{"product_id":"stack-speedybee-f405-v4-bls-60a-30x30-fc-esc","title":"Stack SpeedyBee F405 V4 BLS 60A 30x30 FC\u0026ESC","description":"   \u003cstyle\u003e body { font-family: Arial, sans-serif; font-size: 14px; } for { font-family: Arial, monospace;  white-space: pre-wrap; } .highlight { font-weight: bold;}\u003c\/style\u003e\u003cpre\u003e\nSpeedyBee F405 V4 BLS 60A 30x30 FC\u0026amp;ESC stack\n\nThe fourth version of the SpeedyBee stack includes FC F405 and BLHeli_S 60A ESC. The 30x30mm stack can support up to eight motors, is configured via Bluetooth, has a built-in barometer and ICM42688P gyro. With advanced gyro sensors and intelligent flight algorithms, this pod provides unmatched stability and control, allowing you to perform precise maneuvers with confidence and precision. With a standard 30x30mm form factor, the SpeedyBee stack effortlessly fits most drone frames for hassle-free installation and setup.\n\nSpecifications:\n\nProduct Name: SpeedyBee F405 V4 30x30 Flight Controller\nMCU: STM32F405\nIMU (Gyro): ICM42688P\nUSB port type: Type-C\nBarometer: built-in\nOSD chip: AT7456E chip\nBLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with baud rate 115200 on UART4)\nWIFI: Not supported\nDJI air unit connection method: Two ways are supported: 6-pin connector or direct soldering.\nDJI Air Unit 6 Pin Plug: Supported. Fully compatible with DJI O3\/RunCam Link\/Caddx Vista\/DJI Air Unit V1, no need to change any cable.\nBlackbox MicroSD card slot: Betaflight firmware requires the microSD card type to be either standard (SDSC) or high capacity (SDHC), so extended capacity (SDXC) cards are not supported (many high-speed U3 cards are SDXC). The card MUST also be formatted with a FAT16 or FAT32 file system (recommended). So you can use any SD card smaller than 32GB, but Betaflight can only recognize a maximum of 4GB.\nCurrent sensor input: Supported. For the SpeedyBee BLS 60A ESC, set Scale = 400 and Offset = 0.\nPower Input: 3S - 6S Lipo (via G, BAT pins\/pads from 8-pin connector or 8-pads on bottom)\n5V output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad (used for Buzzer) on the front and 4x LED 5V pads. The total current load is 3A.\n9V output: 2 groups of 9V output, one +9V pad on the front and the other included in the connector on the bottom. The total current load is 3A.\n3.3V output: Supported. Designed for receivers with 3.3V input. Current load up to 500 mA.\n4.5V output: Supported. Designed for the GPS receiver and module, even if the FC is powered via the USB port. Current load up to 1A.\nESC signal: M1 - M4 on the bottom side and M5-M8 on the front side.\nUART: 6 sets (UART1, UART2, UART3, UART4 (reserved for Bluetooth connection)), UART5 (reserved for ESC telemetry), UART6\nESC telemetry: UART R5\nI2C: Supported. SDA \u0026amp; SCL pads on the front. Used for magnetometer, sonar, etc.\nTraditional Betaflight LED Pad: Supported. 5V, G and LED pads on the bottom of the front. Used for WS2812 LEDs controlled by Betaflight firmware.\nBuzzer: BZ+ and BZ- pad used for 5V buzzer\nBOOT Button: Supported\nRSSI Input: Supported. Named as RS on the front.\nSmart Port \/ F.Port: Not supported\nSupported Flight Controller firmware: BetaFlight (default), INAV\nTarget firmware name: SPEEDYBEEF405V4\nMounting: 30.5 x 30.5mm (hole diameter 4mm)\nDimension: 41.6 (L) x 39.4 (W) x 7.8 (H) mm\nWeight: 10.5g\n\nProduct name: SpeedyBee BLS 60A 30x30 4-in-1 ESC\nFirmware: BLHeli_S J-H-40\nPC Configurator download link: https:\/\/esc-configurator.com\/\nContinuous current: 60A * 4\nExplosive current: 80A (10s)\nTVS protection diode: Yes\nExternal capacitor: 1000uF Low ESR capacitor (included)\nESC protocol: DSHOT300\/600\nPower: 3-6S LiPo\nOutput power: VBAT\nCurrent Sensor: Support (Scale=400 Offset=0)\nESC telemetry: Not supported\nMounting: 30.5 x 30.5mm (hole diameter 4mm)\nDimension: 45.6 (L) * 44 (W) * 8 mm (H)\nWeight: 23.5g\n\nThe package includes:\n1x SpeedyBee F405 V4 flight controller\n1x ESC SpeedyBee BLS 60A 4in1\n1x 35V 1000uF Low ESR capacitor \n5x M3 nylon nut\n5x M3 silicone O-ring\n1x M3*8mm silicone grommets (for FC)\n1x M3*8.1mm silicone grommets (for ESC)\n1x SH 1.0mm 25mm long 8pin cable (for FC-ESC connection)\n5x M3*30mm hexagon socket head screws\n1x DJI 6pin cable (80mm)\n1x XT60 power cable (100mm)\n\u003c\/pre\u003e","brand":"Baltic Drones","offers":[{"title":"Default Title","offer_id":55962028507523,"sku":"SB-F4V4-60-STACK","price":101.14,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0936\/1873\/3443\/files\/15729-9_15729-stack-speedybee-f405-v4-bls-60a-30x30-fc-esc.jpg?v=1752052257","url":"https:\/\/p1c5mr-sk.myshopify.com\/products\/stack-speedybee-f405-v4-bls-60a-30x30-fc-esc","provider":"Baltic Drones","version":"1.0","type":"link"}